Gas fireplace service
Sweep & inspection
Caps & crowns
Flue relining
Masonry repairLevel 1 sweep and inspection to the NFPA 211 annual standard - flue, crown, cap, and flashing checked and photographed
Chimney sweep logs do not sweep chimneys. They loosen some creosote - which then falls where a brush and vacuum still have to collect it.
Why Fishers Homeowners Choose HeatShield Chimney Cleaning
We provide independent HeatShield chimney cleaning and repair service in Fishers, IN. HeatShield is a flue resurfacing and relining system, not a sweep brand, so servicing it takes a technician who understands what’s behind the wall. Our technicians have up to 14 years of experience and diagnose HeatShield-lined flues beside original clay-tile flues every week, which means you get an honest answer about repair, resizing or replacement. We are an independent HeatShield service provider and are not affiliated with or authorized by HeatShield. Call (844) 761-5757. We answer 24/7, with fast dispatch from 7am to 7pm.
Why Trust Fishers Chimney Sweep for Your HeatShield Chimney Cleaning?
HeatShield products are poured, wrapped or cast into place. Once they cure, they become part of the flue, and how they wear depends on how they were installed and what surrounds them. Our technicians know the differences between the resurfacing, wrap-around and cast-in-place approaches and can tell from a camera inspection which one you have and what condition it’s in. That matters in Fishers, where a lot of fireplaces are factory-built units in wood-framed chases and the liner interacts with a crown, top plate and cap that take a beating from freeze-thaw.
We use quality parts that fit HeatShield equipment. Proprietary components like top plates, crown products and liner sections have to match the existing system, so we source them from HeatShield or a HeatShield-certified supplier rather than forcing a generic stainless liner into a job where the diameter or insulation spec won’t line up. That keeps the work warranty-safe: a repair done with mismatched parts can void coverage on a liner that was otherwise sound.
We’re a chimney-only specialist, not a generalist handyman or an HVAC add-on. Sweep, inspection and repair all run through the same company, so what a Level 2 inspection finds is what gets fixed. No handoff, no guessing. Call (844) 761-5757 for a free estimate.
Styles & brands we work with
- Sweep & inspection
- Caps & crowns
- Flue relining
- Masonry repair
- Gas fireplace service
Common HeatShield Chimney Cleaning Problems We Fix in Fishers
HeatShield systems fail in specific places, and central Indiana’s weather pushes those places hard. Here’s what we see most often:
- ThermoWrap separation at the flue collar. The wrap edge lifts or delaminates after a few heating seasons, and you may spot a loose edge or rust staining near the top. It usually traces back to movement at the collar, not the liner body failing.
- Resurfacing System cracking along the top 12 to 18 inches. The crown-to-flue joint moves with every freeze-thaw cycle, and the top of a poured liner takes that stress first. A hairline crack up top can let water in long before anything shows lower down.
- Corrosion at the liner-to-top-plate connection. When a cap is missing or poorly fitted, rain and snowmelt sit on the plate and pit the metal. Fishers homes with original builder caps are prime candidates.
- Trapped soot behind an improperly sized ThermoWrap. If the wrap doesn’t match the flue, creosote and soot collect behind it. That causes smoke spillage into the room and speeds up glazing on a wood-burning insert.
- Water intrusion down the chase. In Fishers, the chase-top cap and the wood-framed chase behind it are the usual failure point, not the flue. Rusty caps, failed sealant and ceiling stains near the chase get misread as roof leaks until someone goes up and finds the cap has been leaking for years.
None of these are reason to panic, but they are reason to look. A rust streak or a puff of smoke on a cold start tells you something at the top is moving. If you’ve noticed either, call (844) 761-5757.
HeatShield Parts & Our Repair-vs-Replace Approach
HeatShield components are proprietary. Replacement liner sections, top plates and crown products should come from HeatShield or a HeatShield-certified supplier. A generic stainless liner won’t match the existing diameter or insulation spec, and forcing one in creates a new problem on top of the old one. We don’t stock or carry OEM HeatShield parts; we order what fits your system when we know what the job needs.
We price a targeted repair first. Full relining gets recommended only when the existing liner has failed at multiple joints or the flue is unlined. Here’s how a typical call usually goes: a homeowner notices a rust streak near the top plate or smoke curling from the crown on cold starts. A qualified local technician runs a Level 2 camera inspection, finds a lifted wrap edge or a cracked crown-to-flue joint, and repairs the crown and reseals the top plate rather than replacing the entire liner. The ThermoWrap itself is often still sound below the failure point. That’s the honest answer, and it usually saves real money.
If you’re not sure which side of that line you’re on, call (844) 761-5757 for a free estimate.
Our HeatShield Service Process – Step by Step
- 1
Diagnosis. We start with a Level 2 camera inspection of the flue, the top plate, the crown and the cap. On a HeatShield system we’re looking for wrap separation at the collar, cracking at the crown-to-flue joint, and corrosion where the liner meets the top plate. We photograph what we find so you can see it.
- 2
Repair or install. For a targeted repair we reset or reseal the wrap edge, repair the crown with the right crown product, and reseal the top plate. If the liner has failed at multiple joints, we quote a full reline with matched components.
- 3
Test. We check draft, look for smoke spillage at the firebox, and confirm the cap and top plate are watertight.
- 4
Warranty. We document the parts used and the work done so your HeatShield coverage is protected. Mismatched generic parts are what break a warranty claim, and we don’t use them.
See the difference
Before
After
Before
After
Before
AfterHeatShield Products We Service & Install in Fishers
We service and install the full range of HeatShield systems used in Fishers homes. That includes the HeatShield Resurfacing System, a poured-in-place cement-like liner for damaged clay flues; HeatShield ThermoWrap, an insulated stainless wrap-around liner for unlined or badly cracked flues; HeatShield Thermo-Blend, a cast-in-place liner with insulating aggregate for improved thermal performance; and HeatShield CrownSeal and Crown Repair products, the crown coating and crack repair systems. We handle cap replacement and top-plate resealing to go with them, since that’s where Fishers systems usually fail first.
We Also Service These Brands
HeatShield isn’t the only system we know. We also work with DuraFlex flexible liner systems, installed in-house for complete relining jobs, and Gelco products. We’re also familiar with Olympia Chimney, Famco and Copperfield materials. Being multi-brand means we can match the repair to what’s actually in your chimney instead of steering you toward one product line.
FAQs – HeatShield Chimney Cleaning Service in Fishers
No. We are an independent HeatShield service provider and are not affiliated with, authorized by or certified by HeatShield. Our technicians have up to 14 years of experience working on these systems, and we use quality parts that fit HeatShield equipment.
Yes. HeatShield components are proprietary, so we source replacement liner sections, top plates and crown products from HeatShield or a HeatShield-certified supplier. Generic stainless liners won’t match the existing diameter or insulation spec, and we won’t force one in. Call (844) 761-5757 for a free estimate.
It depends on whether it’s a targeted repair or a full reline. A crown repair and top-plate reseal is usually a straightforward single visit. A full reline with a HeatShield system takes longer because the material has to cure. We set the timeline in the written estimate before any work starts.
We cover the HeatShield Resurfacing System, ThermoWrap, Thermo-Blend, and the CrownSeal and Crown Repair crown products. We also handle cap replacement and top-plate resealing, which matter because that’s where Fishers systems tend to fail first.
Not when it’s done right. Using quality parts that fit the existing system protects your coverage. Generic or mismatched parts are what cause warranty problems. We document the parts used and the work done so you have a record. Call (844) 761-5757 to talk through your system.
There’s no single price because it depends on whether you need a cleaning only, a Level 2 inspection, a crown repair or a full reline. We set the price per job with a written estimate after we’ve seen the flue. The estimate is free, and nothing is recommended without camera evidence you can look at yourself. Call (844) 761-5757 for an exact quote.
Rust at the top of a HeatShield ThermoWrap liner usually comes from water sitting at the liner-to-top-plate connection, not from the liner body failing. In central Indiana’s freeze-thaw cycle, a missing or poorly fitted cap lets rain and snowmelt pit the metal at the top. The fix is often a cap replacement and a resealed top plate, not a new liner. Call (844) 761-5757 and we’ll inspect it before recommending anything.
Yes, when it’s cleaned with the right tools and technique. A poured-in-place liner is a hard surface, but aggressive brushing or the wrong size brush can scratch it. We match the brush to the liner and inspect the top 12 to 18 inches as we go, since that’s where cracking starts.
You don’t guess; you look. A Level 2 camera inspection shows whether the failure is at one joint or many. A single cracked joint at the crown usually gets a targeted repair. Multiple failures or an unlined flue means a full reline. We price the repair first. Call (844) 761-5757 for a free estimate.
It can be, if the sizing and insulation match the insert’s requirements. The wrong size causes smoke spillage and trapped soot behind the liner. We check the flue, the insert and the liner together before we recommend anything.
The cap has to match the top plate you have, and since HeatShield plates are proprietary, a generic cap often doesn’t seal properly. That poor fit is exactly what causes the corrosion and rust staining we see on a lot of Fishers chimneys. We fit the cap to your plate. Call (844) 761-5757 and we’ll take a look.
Book Your HeatShield Service in Fishers, IN
If your HeatShield liner is showing rust at the top, smoke on cold starts or a cracked crown, get it looked at before the heating season. Call Fishers Chimney Sweep at (844) 761-5757 for a free estimate. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday.
Written by the team at Fishers Chimney Sweep.